Focusrite ISA One Single-Channel Mic Preamp/DI

Description

Category
500 Series
Modular Synth
Keyboards
Microphones
Preamps
Dynamics
Equalizers
Monitoring
Computer Audio
Interfaces
Software
Beat Production
Focusrite ISA One Single-Channel Mic Preamp/DI
Focusrite ISA One
features the classic vintage microphone pre-amplifier topology from the original ISA110 module, including the Lundahl L1538 transformer and bespoke zobel network. (The original 110 pre amp formed the cornerstone of each channel of Focusrite's legendary Forte console.)
The pre-amp is complemented by a line input (XLR and TRS Jack) and an independent D.I. channel, complete with dedicated gain control, active or passive impedance switch, a TRS Jack output for routing to an amp and an independent XLR output on the rear. This flexible independent D.I. makes the ISA One ideal both for engineers wishing to blend a D.I.’d guitar signal with a mic’d guitar cabinet, and for demanding performers who require a single classic solution for both guitar and vocals.
A variable impedance circuit has been added, allowing the user to switch between four carefully selected input impedance settings. In addition to the original ISA110 impedance, three further impedance settings allow perfect matching, or creative mismatching of the pre amp with any microphone. ISA One also features an insert point, should the need arise to place extra processing between the pre amp or D.I. and the optional converter. Phantom power, phase reverse and a 75Hz, 18dB/octave high-pass filter are also available from the angled front fascia.
Independent input metering for both channels is provided in the form of a moving coil VU meter with variable calibration to suit analogue and digital recording media, alongside two six-LED peak meters; inputs can be metered either pre- or post-insert. The meter calibrations utilize all the same reference points as Avid's Pro Tools HD system, allowing effortless line-up.
ISA One’s headphone output features a dedicated volume control, which delivers an external stereo cue mix, (a simple click track, or a stereo mix feed from an interface or a live console,) fed to the headphones via two TRS jack inputs on the rear of the unit.
An optional state-of-the-art stereo A-D converter is also available (the same card as used with the ISA430 Mk II), embodying cutting-edge conversion technology seated within Focusrite’s custom analogue circuitry. This optional card can be retrofitted at any time and provides two channels of 24 bit/192kHz A-D conversion with a dynamic range of 119dB.
The ISA microphone pre-amplifier was first introduced back in 1985. This transformer-based pre-amplifier formed the first half of the ISA110 mic-pre and EQ module on Focusrite's critically acclaimed Forte console. This console, and the later Studio console were hailed by many as the finest sounding consoles ever built.
The ISA microphone pre-amplifier went on to form the cornerstone of all ISA and RED Focusrite products. The topology has never changed, except for the addition of a variable impedance circuit, allowing ISA users to either perfectly match the pre-amp with any microphone, thus maximizing level, or to use different settings creatively to shape the sound of the microphone being used. The original ISA110 setting was supplemented by three further impedance settings.
The Focusrite pre amp is renowned for its transparency, but there's also that subtle warmth that transformer core saturation contributes. This seeming contradiction of warmth plus beautifully open, unrestricted high frequencies, is a classic hallmark of the mid 80's Focusrite designs.
With processors whose bandwidth is strictly limited to the audible (20Hz to 20kHz) bandwidth alone, significant roll-off can still occur, affecting the higher audible frequencies of the signal. Therefore, in order to capture every subtle nuance, exactly as it occurs whilst avoiding any roll-off, the pre-amp must operate over a far greater bandwidth. The extremely broad frequency response of Focusrite pre-amps - close to 200kHz at the top end - guarantees accurate phase response across the much narrower range of human hearing, the roll-off point being moved entirely outside of the audible hearing range.
Features:
ISA Series Transformer-based Pre-amplifier -
Encased in a rugged and portable chassis, ISA One offers the classic Focusrite microphone pre-amplifier at its lowest cost to date.
Flexible Independent D.I. Channel -
ISA One is ideal for both engineers and demanding performers alike, featuring independent gain control, an output for routing to an amp, an independent XLR output on the rear and routing to the optional ADC.
Switchable Impedance -
Choose one of four carefully selected input impedances, including the original ISA 110 setting, to suit any microphone.
Optional Stereo 192kHz ADC -
T
his optional card embodies cutting-edge conversion technology, incorporating Focusrite analogue circuitry to deliver the best A-D performance in its class (Dynamic range of 119dB).
Headphone Output with Volume Control -
ISA One can feed either a sum of the two inputs to the headphones output, or an external stereo cue mix (such as a stereo mix feed from an interface) via two TRS Jack inputs on the rear of the unit.
Dedicated Insert Point -
Allows you to place extra processing between the pre-amplifier or D.I. and the optional converter, such as an EQ or compressor.
Mic Input Response
Gain range = 0dB to 60dB in 10dB steps + 20 dB of variable gain
Input Impedance, variable as follows:
(Switched Impedance setting Equivalent Input Impedance at 1kHz)
Low = 600 Ohms
ISA110 = 1400 Ohms
Med = 2400 Ohms
High = 6800 Ohms
EIN (equivalent input noise) = -126dB measured at 60dB of gain with 150 Ohm terminating impedance and 22Hz/22kHz band-pass filter
Noise at main output with gain at unity (0dB) = -97dBu measured with a 22Hz/22kHz band-pass filter
Signal to noise ratio relative to max headroom (9dBu) = 106dB
THD at medium gain (30dB) = 0.0009% measured with a 1kHz -20dBu input signal and with a 22Hz/22kHz band-pass filter
Frequency response at minimum gain (0dB) = -0.5dB down at 10Hz and -3dB down at 125kHz
Frequency response at maximum gain (60dB) = -3dB down at 16Hz and -3dB down 118kHz
CMRR=98dB (Channel 1, 1kHz, maximum gain with +24 dBu input)
Crosstalk Channel to Channel: with 10dB@1kHz input to chA, chB output =104dBrA. With 10dB@10kHz input to chA, chB output = 84dBrA
Line Input Response
Gain range = -20dB to +10dB in 10dB steps + 20 dB of variable gain
Input Impedance = 10k? from 10Hz to 200kHz
Noise at main output with gain at unity (0dB) = -96dBu measured with a 22Hz/22kHz band-pass filter
Signal to noise ratio relative to max headroom (24dBu)=120dB
Signal to noise ratio relative to 0dBFS (+22dBu) = 118dB
THD at unity gain (0dB) = 0.001% measured with a 0dBu input signal and with a 22Hz/22kHz band-pass filter
Frequency Response at unity gain (0dB) = -0.3dB down at 10Hz and -3dB down at 200kHz
Instrument Input Response
Gain range = 10dB to 40dB continuously variable
Input Impedance: • High = greater than1M
Low =greater than 300k
Noise at minimum gain (+10dB) = -92dBu measured with a 22Hz/22kHz band-pass filter
Noise at maximum gain (+40dB) = -62dBu measured with a 22Hz/22kHz band-pass filter
THD at minimum gain (+10dB) = 0.001% measured with a 10dBu input signal and with a 22Hz/22kHz band-pass filter
Frequency Response at 10dB gain with -10dB input = 10Hz-100kHz +/- 0.6dB
Frequency Response at 40dB gain with -40dB input = -2.5dB down at 10Hz and 0dB at 100kHz
High Pass Filter
Roll off = 18dB per octave 3 pole filter
Fixed Frequency 75Hz measured at the 3dB down point
Meters
Moving coil (MC) meter is factory calibrated to 0VU = +4dBu with 1kHz sinewave. With the VU Cal button pressed the meter can be adjusted on the rear panel to allow 0VU to equal +10dBu to +26dBu with the centre detent being equal to +22dBu.
Peak LED meters calibrated in the detent position for 0dBFS = +22dBu, calibration is adjustable on the rear panel to allow 0dBFS to equal +10dBu to +26dBu
Routing for MC and Peak1 meter is after the HPF, pre insert send or switched post insert return. Peak2 is always pre ADC channel 2, which can be fed by external input or Instrument input.
LED levels are as follows when peak calibration is set to center detent on the rear panel. (This is when using the internal ADC). • 0 = +22dBu • -2 = +20dBu • -6 = +16dBu
-12 = +10dBu
-18 = +4dBu
-42 = -20dBu
FRONT AND REAR CONNECTIVITY
Analogue Channel Inputs:
Mic input: XLR x 1
Line input: XLR x 1 and TRS x1
Instrument input TRS Jack: XLR x 1
External ADC input: TRS Jack x 1
Return: TRS Jack x 1
Analogue Channel Outputs:
Send: TRS Jack x 1
Balanced line output: XLR x 1
DI output: XLR x 1
DI through: TS Jack x 1
Analogue Channel Additional I/O:
Cue mix left input: TRS Jack x 1
Cue mix right input: TRS Jack x 1
Headphones output: ¼” TRS Jack x 1
Weight
8.6Ibs
Dimensions
8.66" (W) x 4.1" (H) x 10" - 11.4" (D - top to bottom)
About Us
Since 1993, we have been committed to equipping our customers with the very best gear, advice, and personal service anywhere. We believe that great sound can be achieved at any budget. We also believe that the ambitions of our customers should always come first. For us, it's about building long-lasting relationships, not just selling gear. And over the years, those beliefs have turned customers into friends and family. Whether you're just starting out, or a seasoned pro, we're here for you, no matter where your audio travels may take you.
Shipping Policy
Free ground shipping to the lower 48 states Via FedEx. All of our items ship via FedEx. On checkout, it may look like you are selecting a UPS shipping method, but the item will be shipped via the equivalent FedEx method.
Import Duties and Tax
Since import taxes and/or duties that your government might impose on products shipped from the United States may apply, you (the customer), are solely responsible for shipping charges, taxes, and duties, once goods arrive in your country.
Undeliverable/Rejected Package
If your package was rejected by your local Customs Bureau or the shipment could not be delivered and was returned to Vintage King Audio for any reason, we are not responsible for the shipping costs.
Free Extended Warranty
All new items that Vintage King carries are subject to our FREE extended warranty protection. Basically, if the manufacturer offers a 1-year warranty on your product, then you are covered under the same warranty terms for a total of 2 years from the time of initial shipment. Likewise, if the manufacturer offers a 5-year warranty, then you receive a total of 6 years of coverage when purchased through Vintage King. We add 1 year to your standard manufacturer's warranty period, FREE of charge, whatever the manufacturer's warranty period may be.
Duties and tax for warranty and damage replacement items
International Duties and tax for warranty and damage replacement items may apply. Even though you may have paid shipping, taxes or duty on your original order, it is IMPORTANT to understand that your government may impose duties and taxes for warranty items or replacement items damaged during shipment from the United States for the new order. You (the customer), are solely responsible for shipping charges, taxes, and duties, once goods arrive in your country.
Used Item Warranties
Vintage King offers an industry-leading level of technical service and warranty support on our used and vintage items. Our used item warranty periods are as follows:
Analog Outboard Gear – 1 Year
Microphones – 1 Year (excluding capsules, tubes, and ribbon elements)
Speakers – 1 Year (excluding drivers)
Digital Outboard Gear – 30 Days
Return Policy
We do our best to help you choose the perfect gear, but if you don't love it in the first 30 days after receipt, please contact us through eBay for a return authorization.
Note:
Software is not returnable or refundable.
What Are "Demo Deal" or "B-Stock" Products?
Our Demo Deals and B-Stock products offer a unique opportunity to save big on near-mint condition, fully warrantied gear. These items have been opened for demonstration purposes and put back in the box without extended use. All original factory accessories and packaging are included.
In addition to the manufacturer's warranty, Demo Deal and B-Stock items also come with an additional 1-year of warranty coverage from Vintage King, free of charge, so rest assured that not only are you saving big by purchasing a Demo Deal/B-Stock item, but you will also receive the same level of world-class support from Vintage King as with the purchase of a factory-sealed unit.
Taxes
Vintage King collects sales tax for shipments to Alabama, Arkansas, Arizona, California, Colorado, Connecticut, Georgia, Hawaii, Idaho, Illinois, Indiana, Iowa, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, Nevada, New Jersey, New Mexico, New York, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Utah, Vermont, Virginia, Washington, Washington D.C., Wisconsin and Wyoming. Partial and complete tax exemptions may be available in your state. Contact us through eBay for details.
Note:
eBay may collect sales tax in states not listed above.